

The Schneider Electric Acti9 REDs A9CR4240 residual current recloser combines a 2-pole, 40 A, 30 mA type A residual current device with an automatic reclosing system. When a residual current trip occurs, the unit checks the downstream circuit insulation before attempting to restore the supply, helping maintain service continuity without compromising installation safety.
The Acti9 REDs is especially suitable for installations where a transient trip could leave important equipment without power for long periods. If the insulation fault disappears and the device determines that conditions are suitable, it automatically resets; if the fault remains, it blocks reconnection and continues monitoring the insulation.
Reference A9CR4240 has a bipolar configuration and is designed for single-phase 230 V AC networks.
The Schneider Electric Acti9 REDs A9CR4240 uses type A residual current protection, capable of detecting sinusoidal alternating residual currents and pulsating direct currents.
Its 30 mA sensitivity is intended to protect people against risks arising from insulation faults and electric shock, within a properly designed installation and in compliance with applicable regulations.
The main feature of the REDs is its ability to check circuit insulation before reclosing. After a residual current trip, the system analyses the downstream circuit and only allows reconnection when insulation conditions are suitable.
For the 30 mA version, Schneider Electric specifies the following reference levels:
When insulation resistance is above 16 kΩ, the system can authorise reclosing. If it is below 8 kΩ, the device prevents reconnection. This avoids automatically restoring power when a dangerous insulation fault persists.
Residual current trips can be caused by transient faults that disappear without manual intervention. In these situations, the Acti9 REDs can automatically restore power after verifying that the circuit once again presents suitable conditions.
This function is especially useful in unattended installations or where a prolonged interruption may affect the operation of electrical equipment.
The A9CR4240 includes specific logic to manage reconnection attempts and prevent repeated reclosing on a faulty installation.
One of the main differences of the REDs version is its extended monitoring system. If the device detects that insulation does not allow safe reconnection, it does not force the residual current device to close.
When a fault is present, the system continues performing an insulation diagnostic approximately every 2 minutes. When the fault disappears and the required conditions are met, the system can automatically restore service.
This feature provides greater supply continuity than systems limited to a fixed number of reclosing attempts.
The recloser includes local signalling to make it easier to monitor the device from the electrical panel itself.
These indications make it possible to visually check whether the residual current device is connected and to know the status of the reclosing system.
The Schneider Electric A9CR4240 is a RCCB residual current circuit breaker with automatic reclosing device. Therefore, it protects against residual currents, but does not include thermal protection against overloads or magnetic protection against short circuits.
The installation must include overcurrent protection correctly coordinated with the REDs, using the appropriate circuit breaker or fuse according to Schneider Electric’s tables and requirements.
The device offers insulation characteristics suitable for low-voltage electrical panels:
The Acti9 REDs A9CR4240 is designed for fixed installation on a 35 mm symmetrical DIN rail. It occupies 6 modules of 9 mm, equivalent to a width of 54 mm.
The power terminals allow the use of different conductor types with a cross-section of up to 35 mm².
The residual current recloser has an IP20 protection rating and is intended for installation inside a suitable electrical enclosure or panel.
The Schneider Electric A9CR4240 offers mechanical durability of up to 4,000 opening and closing cycles, providing a long service life for applications where periodic switching may occur.
Automatic reclosing with prior insulation checking makes this device especially interesting in circuits where restoring supply after a transient fault is important.
Suitability for each circuit must be checked according to the installation characteristics and the requirements for service continuity and safety.
The Acti9 REDs is developed in accordance with EN/IEC 63024, the standard applicable to automatic reclosing devices for circuit breakers and residual current devices for domestic and similar use.
The Schneider Electric Acti9 REDs A9CR4240 2-pole, 40 A, 30 mA type A residual current recloser combines residual current protection and intelligent automatic reclosing to improve service continuity. Its prior insulation check prevents reconnection while a fault persists and allows power to be restored automatically when the issue is transient, making it a particularly useful solution for homes, tertiary installations and circuits that cannot remain disconnected unnecessarily.