

The Schneider Electric Acti9 Quick Vigi iC60 A9Q14240 is a residual current block with 2 poles, 40 A and 300 mA sensitivity, designed to add residual current protection to compatible circuit breakers in the Acti9 iC60 and Reflex iC60 range. It is an instantaneous type AC device, intended to detect sinusoidal alternating residual currents and protect the installation against insulation faults, indirect contact and fire risks associated with current leakage.
The Quick Vigi A9Q14240 uses voltage-independent tripping technology and is coupled to the compatible circuit breaker to form a complete protection assembly. In this way, the Vigi block provides the residual current function while the associated circuit breaker provides overload and short-circuit protection.
Reference A9Q14240 features 2 poles, a rated current of 40 A and a residual current sensitivity of 300 mA. Its operation is instantaneous, with no intentional time delay, and it belongs to AC class.
A 300 mA sensitivity is mainly intended to protect installations against insulation faults and fire risk, while also providing protection against indirect contact within the conditions established by regulations and the installation design.
Type AC is designed to detect sinusoidal alternating residual currents. This makes the A9Q14240 suitable for circuits and loads where this is the expected fault current type.
The choice between type AC, A, A-SI or other residual current protection classes should be made according to the connected loads, the characteristics of the installation and the applicable regulatory requirements.
Residual current detection and tripping in the Quick Vigi iC60 are carried out using voltage-independent technology. This feature means that the residual current function does not rely on an auxiliary electronic supply to trip when a residual current above the set threshold is detected.
The A9Q14240 is designed as an additional residual current block, so it must be associated with a compatible Schneider Electric circuit breaker. Schneider Electric specifies compatibility with the Acti9 iC60 and Acti9 Reflex iC60 families.
Once coupled to the corresponding circuit breaker, the assembly can provide protection against residual currents, overloads and short circuits. Therefore, the A9Q14240 should not be considered a circuit breaker on its own, but rather the module that adds the residual current function to the protection assembly.
The block includes local trip indication via the VisiTrip system. The visible mechanical indicator on the front makes it easy to identify that the residual current protection has operated, helping to locate the source of a disconnection within the electrical panel more quickly.
This feature is especially practical in panels with multiple protections, as it makes diagnosis and maintenance easier.
The Quick Vigi design is intended to simplify assembly with the compatible circuit breaker. The electrical connection to the circuit breaker is plug-in and the assembly is ready for installation on a DIN rail.
The block also supports compatible comb busbars on the lower side, making power distribution easier inside correctly configured Acti9 modular panels.
The Schneider Electric A9Q14240 has a width of 36 mm, equivalent to four 9 mm pitches or two standard 18 mm modules. Its overall dimensions are 91 mm high, 36 mm wide and 73.5 mm deep.
Its modular format allows it to be installed alongside other Acti9 protections, making efficient use of the available space in the electrical panel.
The lower tunnel terminals allow connection of rigid conductors up to 35 mm² and flexible conductors up to 25 mm². The recommended stripping length is 14 mm and the specified tightening torque is 3.5 Nm.
These features make for a robust connection of the residual current block in installations correctly sized for a rated current of up to 40 A.
The Quick Vigi iC60 A9Q14240 has a rated insulation voltage of 500 V AC and a rated impulse withstand voltage of 6 kV. It also has a pollution degree 3, according to the specifications indicated for the device.
The residual current block has an IP20 degree of protection as a modular device and can reach IP40 when installed in a suitable enclosure. It is designed to operate in ambient temperatures between -5 and 60 °C and can be stored between -40 and 85 °C.
The Schneider Electric A9Q14240 complies with the requirements of EN/IEC 61009-1 and EN/IEC 61009-2-1 applicable to residual current protective devices with overcurrent protection when correctly configured with the compatible circuit breaker.
The Schneider Electric Quick Vigi iC60 A9Q14240 is a modular solution for adding 300 mA type AC residual current protection to electrical panels equipped with compatible Acti9 iC60 or Reflex iC60 circuit breakers. Its 40 A rated current, instantaneous tripping, voltage-independent technology, VisiTrip indicator and quick connection system make it possible to configure a compact, professional protection solution for low-voltage electrical installations.