

The Schneider Electric Acti9 iC60N A9F75425 thermal-magnetic circuit breaker is a modular automatic switch with 4 protected poles, 25 A and D curve, designed to protect electrical circuits against overloads and short circuits. It offers a rated breaking capacity Icn of 6 kA at 400 V AC according to IEC/EN 60898-1 and an ultimate breaking capacity Icu of 10 kA at 380-415 V AC according to IEC/EN 60947-2. Its D curve makes it suitable for loads with high inrush currents, while the VisiTrip and VisiSafe technologies make it easier to identify tripping and verify the safe status of the circuit.
Reference A9F75425 belongs to Schneider Electric's Acti9 iC60N range and combines thermal-magnetic tripping, class 3 current limiting, suitability for isolation and DIN rail mounting. Its four-pole configuration and compatibility with auxiliaries and Vigi residual current blocks allow it to be integrated into professional distribution boards, tertiary installations and industrial applications with loads that require a D tripping curve.
The Schneider Electric A9F75425 features 4 poles and 4 protected poles. This means that the four conductors connected to the breaker are protected against overcurrents and are disconnected together when the device operates.
The Acti9 iC60N combines two protection principles:
In this way, the A9F75425 protects the circuit against the main risks caused by overcurrent.
Schneider Electric specifies a magnetic tripping threshold of 12 × In ±20 % for this reference.
The D curve allows it to tolerate higher inrush current peaks than B or C curve devices, so it may be suitable, subject to installation calculations, for loads such as:
Due to its high magnetic threshold, it is especially important to check that the minimum available fault current is sufficient to ensure disconnection within the required times.
In accordance with IEC/EN 60898-1, the A9F75425 has a rated breaking capacity Icn of 6,000 A at 400 V AC and 50/60 Hz.
The service breaking capacity Ics at 400 V according to the same standard is also 6 kA, equivalent to 100% of Icn.
When evaluated according to IEC/EN 60947-2, the breaking capacity depends on the network voltage:
Therefore, the commercial values of 6 kA and 10 kA are both correct, but they correspond to different standards and test conditions.
According to IEC/EN 60947-2, Schneider Electric specifies:
The iC60N A9F75425 has energy limiting class 3 according to IEC/EN 60898-1.
This capability limits the energy passing through the installation during a short circuit, reducing thermal and electrodynamic stress on downstream conductors and equipment.
The VisiTrip technology provides local indication that makes it easy to locate the circuit breaker that has operated due to a fault.
This function is especially useful in boards with numerous circuits, as it reduces the time needed to identify the tripped protection device.
The VisiSafe system provides a contact position indication that allows you to visually confirm that the circuit is open.
In addition, the A9F75425 is declared suitable for isolation in accordance with IEC/EN 60898-1 and IEC/EN 60947-2.
The Acti9 iC60 range uses a Fast Closing mechanism, which makes the contact closing speed independent of how quickly the operating lever is manually actuated.
This feature helps provide consistent switching and reduce contact wear.
The Schneider Electric A9F75425 is designed for fixed mounting on a DIN rail, making it easy to integrate with other Acti9 modular devices.
The terminals allow connection from the top or bottom and accept compatible distribution combs.
The iC60N can be complemented with different compatible accessories to expand the functions of the board:
The exact compatibility should be checked according to the specific accessory reference.
The A9F75425 is a thermal-magnetic circuit breaker. Its function is to protect against overloads and short circuits.
It does not itself include residual current protection against earth leakage. When required by the installation, it must be combined with a compatible Vigi block or with a properly selected residual current protection device.
These ratings make the device suitable for professional boards subject to normal switching, disconnection and maintenance operations.
The A9F75425 has an IP20 protection rating in accordance with IEC 60529.
It must be installed inside a suitable enclosure or panel that provides the environmental protection level required for the application.
With its 25 A rating and D curve, this reference is especially suitable for circuits that may present high starting currents, provided that protection calculations confirm its suitability.
The Schneider Electric Acti9 iC60N A9F75425 combines four protected poles, 25 A and D curve in a modular device designed for circuits with high inrush currents. Its breaking capacity reaches 6 kA Icn at 400 V according to IEC/EN 60898-1 and 10 kA Icu at 380-415 V according to IEC/EN 60947-2.
The VisiTrip, VisiSafe and Fast Closing technologies, together with compatibility with auxiliaries and Vigi blocks, make it easier to create professional distribution boards with improved diagnostics and maintenance.
Important: the D curve has a high magnetic threshold, so before using the A9F75425 you must check the design current, conductor cross-section, minimum and maximum short-circuit current, circuit impedance and required breaking capacity. This circuit breaker does not include residual current protection against earth leakage.