

The Schneider Electric Acti9 iK60N A9K24240 thermal-magnetic circuit breaker is a modular 2-pole, 40 A, C-curve automatic switch designed to protect electrical circuits against overloads and short circuits. It features thermomagnetic protection on both poles and offers a rated breaking capacity Icn of 6 kA according to EN/IEC 60898-1, making it a suitable solution for residential, commercial, and tertiary electrical distribution boards.
It belongs to Schneider Electric’s Acti9 iK60 range and is designed for modular mounting on DIN rail. Its mechanism combines thermal protection for prolonged overloads and magnetic tripping for short circuits, with a C-curve tripping characteristic and a magnetic threshold between 5 and 10 times the rated current.
The A9K24240 integrates two complementary protection mechanisms. The thermal trip operates when the circuit carries a current above the permissible level for a certain time, protecting conductors and equipment against the effects of overload.
The magnetic trip, on the other hand, responds quickly to high-intensity currents associated with a short circuit. This combination makes the iK60N a complete protection device against overcurrents within the operating conditions established by Schneider Electric.
The A9K24240 reference has 2 poles and both are protected. This means that each pole includes overload and short-circuit protection and that both open simultaneously when a trip or manual operation occurs.
This configuration is suitable for circuits where bipolar disconnection is required while maintaining thermomagnetic protection on both conductors.
The breaker has a rated current In of 40 A at a reference temperature of 30 °C. This value should be considered together with conductor cross-section, ambient temperature, circuit grouping, and installation method.
The rated current of the MCB must be selected so that it adequately protects the installed wiring and matches the expected circuit demand.
The Schneider Electric A9K24240 uses a C curve. The technical data sheet specifies a magnetic tripping threshold of 5 to 10 times the rated current.
With a rated current of 40 A, this behavior allows certain transient current surges while maintaining a fast response to short circuits. The C curve is commonly used in distribution circuits and loads with moderate inrush currents.
The Acti9 iK60N A9K24240 has a rated breaking capacity Icn of 6,000 A according to EN/IEC 60898-1. Schneider Electric’s current documentation states this value at 230 and 400 V AC, 50/60 Hz, depending on the published version of the data sheet.
The manufacturer also specifies a service breaking capacity Ics of 6 kA, equivalent to 100% of Icn. The selected breaking capacity must be equal to or greater than the prospective short-circuit current at the installation point of the breaker.
This breaker has a Class 3 energy limiting rating in accordance with EN/IEC 60898-1. This capability helps limit the energy and current flowing through the circuit during a short circuit.
Good current limiting reduces the thermal and electrodynamic stresses that conductors and other downstream electrical equipment must withstand.
Schneider Electric specifies the A9K24240 as suitable for isolation according to EN/IEC 60898-1. This feature allows the breaker to be used to isolate the circuit within the conditions defined by the standard and the manufacturer.
The front operating handle includes local ON/OFF indication to make it easier to monitor the device status.
The Acti9 iK60 range allows electrical supply from either the top or the bottom, providing greater flexibility during internal panel distribution.
This feature makes it easier to adapt wiring to different busbar configurations and component layouts.
The design includes a double clip that makes it easier to remove the breaker even when a comb busbar is installed. This solution simplifies installation and device replacement tasks inside the panel.
Using compatible busbar systems allows for neater distributions and reduces part of the individual wiring between breakers.
The A9K24240 is designed for clip-on mounting on a DIN rail. It occupies four 9 mm pitches, equivalent to 2 modules of 18 mm.
Its modular format makes it easy to integrate alongside residual current devices, contactors, relays, and other protection or control devices inside electrical panels.
The breaker uses tunnel terminals accessible from the top or bottom. The technical data sheet specifies the following connection capacities:
The final conductor cross-section must be selected according to design current, installation method, temperature, voltage drop, and applicable electrical regulations.
The A9K24240 has a rated insulation voltage Ui of 440 V AC at 50/60 Hz and an impulse withstand voltage Uimp of 4 kV.
These characteristics define the dielectric behavior of the device against permanent insulation voltage and transient overvoltages within the conditions specified by EN/IEC 60898-1.
Schneider Electric declares a high service life for this MCB:
These performance levels make the iK60N suitable for panels where a modular device with a long service life is required within the conditions specified by the manufacturer.
The device has an IP20 protection rating according to IEC 60529. It is intended to be installed inside panels or enclosures that provide the level of protection required by the environmental conditions of the site.
The manufacturer also specifies a pollution degree 2 and overvoltage category II within the conditions stated in the technical data sheet.
The iK60N is designed to operate within a wide temperature range:
In installations subject to high temperatures or special conditions, the thermal behavior of the assembly should be checked and, where appropriate, the correction factors defined by Schneider Electric should be applied.
The A9K24240 provides thermal-magnetic protection against overloads and short circuits, but it does not include residual current protection against earth leakage currents.
When the installation requires residual current protection, it must be complemented with a suitable residual current device, selected according to the sensitivity, class, and requirements established by the project and applicable regulations.
Thanks to its features, this MCB is suitable for different low-voltage distribution circuits:
The Schneider Electric A9K24240 provides bipolar protection against overloads and short circuits with a rated current of 40 A, C curve, and 6 kA breaking capacity. Its two protected poles, Class 3 limiting performance, and suitability for isolation make it ideal for distribution boards where compact and easy-to-install modular protection is required.
DIN rail mounting, the option of top or bottom supply, and the double clip compatible with comb busbars make both initial installation and later maintenance easier. For correct protection, the MCB should be selected together with the conductor cross-section, the expected short-circuit current, and the rest of the circuit protection devices.