

The Schneider Electric TeSys K LC1K0910M7 mini contactor is a compact 3-pole contactor with 3 normally open main contacts, designed for switching electric motors and resistive loads. It offers a rated current of 9 A in AC-3 and AC-3e categories up to 440 V, can control motors up to 4 kW at 380-415 V, and includes a 220-230 V AC control coil at 50/60 Hz. It also integrates 1 normally open auxiliary contact and uses screw terminals, bringing the main switching functions into a body only 45 mm wide.
The LC1K0910M7 reference belongs to Schneider Electric’s TeSys K range, developed for applications where high switching capacity is needed while taking up very little space in the panel. It is a suitable solution for motors, pumps, fans, HVAC, machinery, and automation systems where the available control signal is 220-230 V AC.
The LC1K0910M7 features 3 normally open main poles. When the coil is energized, the three power contacts close simultaneously to connect the load; when coil power is removed, they return to the open position.
Schneider Electric specifies the following motor power ratings in AC-3 category:
In a typical 400 V three-phase network, the LC1K0910M7 can therefore switch a motor up to 4 kW, provided its rated current and starting conditions are compatible with the contactor’s 9 A AC-3 rating.
The M7 suffix identifies this version with a 220-230 V AC control coil at 50/60 Hz.
It can be used with control circuits made up of elements such as:
Schneider Electric specifies a coil operating range of approximately 0.8 to 1.15 times Uc at temperatures below 50 °C.
The control circuit has low consumption, suitable for compact panels:
These values make it possible to correctly size control transformers, interface relays, and other components used to energize the coil.
In addition to the three main power contacts, the LC1K0910M7 includes from the factory 1 normally open, instantaneous auxiliary contact.
The auxiliary contact can be used for self-holding functions, run indication, feedback to a control system, or electrical interlocking.
In addition to motor control, the TeSys K LC1K0910M7 can be used to switch resistive or slightly inductive loads. Schneider Electric specifies a 20 A utilization current in AC-1 category.
This value should not be confused with the 9 A in AC-3/AC-3e: the categories represent different operating conditions.
Schneider Electric specifies a rated making capacity Irms of 110 A AC in accordance with IEC 60947.
The rated breaking capacity reaches:
These values correspond to the contactor’s switching performance and must not be interpreted as short-circuit breaking capacity.
The LC1K0910M7 is a switching and control device. It does not include overload or short-circuit protection by itself.
Schneider Electric specifies the following associated protection devices:
In motor applications, it can be combined with a correctly selected and coordinated motor protection circuit breaker or thermal overload relay.
The LC1K0910M7 reference uses screw terminals for power, control, and signaling connections.
Depending on the type and number of conductors, it accepts connections of up to approximately 4 mm². The use of screw terminals provides a simple solution widely used in automation panels and machinery.
The mini contactor can be installed by:
This flexibility makes it suitable for both small control panels and larger industrial enclosures.
One of the main advantages of the TeSys K range is its reduced size:
These dimensions allow three power poles and one integrated auxiliary contact to be housed in very little space inside the electrical panel.
The LC1K0910M7 supports a maximum operating frequency of up to 3,600 cycles per hour within the conditions specified by Schneider Electric.
The indicated operating times are approximately:
Schneider Electric specifies high durability for the TeSys K range:
Effective electrical life depends on current, voltage, load type, utilization category, and switching frequency.
The main dielectric characteristics include:
The TeSys K range is designed for use in professional panels and machinery equipment within the conditions indicated by Schneider Electric.
Its combination of 9 A AC-3, motor capacity up to 4 kW at 400 V, and 220-230 V AC coil makes it suitable for many switching systems:
The Schneider Electric TeSys K LC1K0910M7 combines 9 A in AC-3/AC-3e, motor capacity up to 4 kW at 400 V, and a 220-230 V AC 50/60 Hz coil in a device measuring only 45 x 58 x 57 mm. The built-in NO auxiliary contact makes interlocking and signaling functions easier without the need to add an external auxiliary block initially.
Its compact format, DIN rail or panel mounting, high switching frequency, and compatibility with TeSys protection devices and accessories make it a particularly practical solution for machinery, HVAC, and automation.
Important: the LC1K0910M7 is a switching device and not a motor protection device. It does not protect by itself against overloads or short circuits, so it must be combined with a motor protection circuit breaker, thermal overload relay, fuses, or a correctly sized and coordinated circuit breaker.