

The Schneider Electric TeSys Deca LC1DT25P7 contactor is a 4-pole contactor with 4 normally open main contacts (4 NO), designed for switching resistive loads up to 25 A in AC-1 category. It features a 230 V AC control coil at 50/60 Hz and two built-in auxiliary contacts, 1 NO + 1 NC, providing a compact and reliable solution for electrical panels, automation, industrial installations, and HVAC applications.
The LC1DT25P7 reference belongs to Schneider Electric’s TeSys Deca range and supports a rated operational current of 25 A up to 440 V AC in AC-1. Its 45 mm wide design allows installation on DIN rail or by screw fixing on a plate, making it easy to integrate into control and distribution panels.
The LC1DT25P7 features 4 power poles, all normally open. When the coil is energized, the four main contacts change state simultaneously and allow the connected load to be supplied.
Its four-pole configuration is especially useful in installations where four conductors need to be switched simultaneously by a single device.
The P7 version includes an electromagnetic coil of 230 V AC compatible with 50 and 60 Hz networks. This voltage applies exclusively to the contactor control circuit and must be taken into account when designing the control scheme.
In addition to the four power main contacts, the Schneider Electric LC1DT25P7 includes as standard one normally open auxiliary contact and one normally closed auxiliary contact.
These auxiliary contacts allow signaling, interlocking, and control logic functions without the immediate need to install an additional auxiliary block. The NC contact also features a certified mirror contact function.
Schneider Electric specifies this model primarily for non-inductive or resistive loads in AC-1 category. This category includes applications where the inrush current does not present the high peaks characteristic of direct starting of certain motors.
The contactor supports a rated operational current of 25 A at ambient temperatures up to 60 °C and voltages up to 440 V AC within the AC-1 category.
For this reason, for specific motor control applications, the appropriate TeSys reference and utilization category should be verified according to the motor power, voltage, and switching type.
The LC1DT25P7 is designed for installations with frequent switching operations. Schneider Electric specifies a maximum operating frequency of up to 3,600 cycles per hour at 60 °C.
Its rated making and breaking capacity in the power circuit reaches 250 A at 440 V under the conditions defined by IEC 60947.
The TeSys Deca contactor is designed to withstand a high number of operations over its service life. Schneider Electric declares a mechanical durability of up to 15 million cycles.
Under AC-1 use at 25 A and voltages up to 440 V, the electrical durability reaches approximately 0.8 million cycles.
The Schneider Electric LC1DT25P7 can be installed directly on a DIN rail or fixed with screws on a panel, providing flexibility during electrical cabinet assembly.
Its compact body of only 45 mm width makes it easy to integrate alongside protection devices, relays, control devices, and other automation components.
The LC1DT25P7 reference uses screw terminals to ensure a secure conductor connection and to simplify installation and maintenance operations.
The TeSys Deca system is designed for integration into professional panels and supports different compatible accessories and auxiliary blocks from the Schneider Electric family.
The contactor offers electrical characteristics suitable for demanding industrial and commercial applications. Its rated impulse withstand voltage Uimp is 6 kV according to IEC 60947 and it belongs to overvoltage category III.
The front part of the contactor has an IP20 protection rating according to IEC 60529. It is designed to be installed inside suitable electrical enclosures and cabinets.
The device withstands environmental conditions typical of industrial applications, with an operating temperature range of -40 °C to 60 °C without derating. It can be used up to 70 °C applying the derating conditions indicated by Schneider Electric.
The Schneider Electric TeSys Deca LC1DT25P7 complies with different international standards applicable to contactors and low-voltage control equipment.
In addition, the range has various international certifications to facilitate its use in industrial and commercial projects.
The Schneider Electric TeSys Deca LC1DT25P7 is a compact and robust solution for switching resistive loads in professional installations. Its 4 NO main contacts, 25 A AC-1 current, 230 V AC 50/60 Hz coil, and 1 NO + 1 NC auxiliary contacts make it suitable for automation panels, HVAC systems, and other electrical control applications.
Its high durability, DIN rail or panel mounting, and compatibility with TeSys Deca accessories provide a flexible solution for installations where four poles need to be controlled simultaneously with a 230 V AC control signal.