Contactor 32A 1 NO/1 NC 110V 50-60HZ with reference LC1D32F7 from the brand SCHNEIDER ELECTRIC
Contactor 32A 1 NO/1 NC 110V 50-60HZ with reference LC1D32F7 from the brand SCHNEIDER ELECTRIC
SCHNEIDER ELECTRIC

Contactor 32A 1 NO/1 NC 110V 50-60HZ

REF
LC1D32F7
(0)
131.10 €
€131.10
€333.82
Up to -6% for professionals. Discover it.
Schneider Electric TeSys Deca 3P 32A AC-3 contactor, 110V AC 50/60Hz coil, 3 NO power contacts and 1 NO + 1 NC auxiliary contacts, for motors up to 15 kW at 400V.
Buy now and receive it between 20 and November 23
Express delivery
Get +132 +263 Sumis for the purchase
Receive 2x Sumis for a limited time
More about the product

Information about Contactor 32A 1 NO/1 NC 110V 50-60HZ

The Schneider Electric LC1D32F7 contactor from the TeSys D / TeSys Deca range is a three-pole contactor designed for motor control and resistive loads in industrial, commercial, and automation systems. It offers a rated operational current of 32 A in AC-3 category up to 440 V, includes a 110 V AC control coil at 50/60 Hz, and can control three-phase motors up to 15 kW at 380-400 V.

The device features 3 normally open main contacts for the power circuit and 1 normally open auxiliary contact + 1 normally closed auxiliary contact integrated. This configuration makes it easy to implement interlocking, signaling, and automation circuits without needing to install an additional auxiliary block from the outset.

Key features of the Schneider Electric LC1D32F7

  • Brand: Schneider Electric.
  • Range: TeSys.
  • Family: TeSys D / TeSys Deca.
  • Reference: LC1D32F7.
  • Type: power contactor.
  • Application: motor control and resistive loads.
  • Number of poles: 3P.
  • Main contacts: 3 NO.
  • Integrated auxiliary contacts: 1 NO + 1 NC.
  • Rated current AC-3: 32 A up to 440 V.
  • Rated current AC-1: 50 A up to 440 V.
  • Coil voltage: 110 V AC.
  • Coil frequency: 50/60 Hz.
  • Motor power at 380-400 V: 15 kW in AC-3.
  • Motor power at 415-440 V: 15 kW in AC-3.
  • Power circuit operating voltage: up to 690 V AC.
  • Mounting: DIN rail or plate.
  • Terminals: screw terminals.
  • Front protection rating: IP20.
  • Dimensions: 45 x 85 x 92 mm.
  • Weight: approximately 0.375 kg.

32 A contactor for motor control

The LC1D32F7 is specifically designed for starting and stopping electric motors. In AC-3 category, it supports a rated current of 32 A up to 440 V AC at temperatures up to 60 °C, allowing it to control asynchronous motors within the conditions specified by Schneider Electric.

AC-3 category covers common applications where the contactor closes on the motor starting current and opens when the motor is running normally. For this reason, this reference is suitable for pumps, fans, compressors, machinery, and many electrical drives.

Up to 15 kW motor power at 400 V

The maximum motor power depends on the supply voltage. Schneider Electric specifies for the LC1D32F7:

  • 220-230 V AC: 7.5 kW in AC-3.
  • 380-400 V AC: 15 kW in AC-3.
  • 415-440 V AC: 15 kW in AC-3.
  • 500 V AC: 18.5 kW in AC-3.
  • 660-690 V AC: 18.5 kW in AC-3.
  • 400 V AC in AC-4: 7.5 kW.

In a typical 400 V three-phase installation, this reference can therefore control motors up to 15 kW in AC-3 category, provided that the rated current and the actual motor characteristics remain within the contactor limits.

110 V AC coil at 50/60 Hz

The F7 version includes an electromagnetic coil rated at 110 V AC at 50/60 Hz. This control voltage makes it easy to integrate into automation panels and control circuits operating at 110 V.

When the coil is energized, the contactor actuates its power and auxiliary contacts simultaneously. When the control signal disappears, the mechanism returns to its rest position.

Schneider Electric specifies a coil operating range of approximately 0.8 to 1.1 times Uc at 50 Hz and 0.85 to 1.1 times Uc at 60 Hz, within the temperature conditions indicated by the manufacturer.

3 normally open power contacts

The main circuit has three normally open contacts, one for each phase. These contacts are responsible for connecting and disconnecting the three-phase load supply.

It is important to distinguish these three main contacts from the 1 NO + 1 NC indicated in the commercial title, which correspond to the standard integrated auxiliary contacts.

Integrated 1 NO + 1 NC auxiliary contacts

The LC1D32F7 includes one normally open auxiliary contact and one normally closed auxiliary contact as standard. They can be used for different automation functions:

  • Contactor self-holding.
  • Status indication.
  • Electrical interlocking.
  • Feedback to PLCs or controllers.
  • Auxiliary relay control.
  • Interlocking with other contactors.

The auxiliary contacts are mechanically linked in accordance with IEC 60947-5-1. The NC contact also features mirror contact function in accordance with IEC 60947-4-1.

32 A in AC-3 and 50 A in AC-1

The permissible current depends on the nature of the load and the utilization category:

  • AC-3: 32 A up to 440 V and 60 °C.
  • AC-1: 50 A up to 440 V and 60 °C.

AC-3 is mainly intended for motor switching, while AC-1 applies to non-inductive or slightly inductive loads. Therefore, the contactor must always be selected considering the utilization category as well as the rated current.

Power voltage up to 690 V AC

The power circuit supports a rated operational voltage of up to 690 V AC between 25 and 400 Hz. Schneider Electric also allows use in direct current up to 300 V within the specified configurations.

The rated insulation voltage is 690 V according to IEC 60947-4-1 and the rated impulse withstand voltage Uimp is 6 kV, with overvoltage category III.

Making and breaking capacity

The contactor offers a rated making capacity of 550 A at 440 V for the power circuit in accordance with IEC 60947. The rated breaking capacity is also 550 A at 440 V.

These performance values allow it to withstand the transient currents generated during motor switching and other compatible loads.

Conventional thermal current of 50 A

Schneider Electric specifies a conventional free-air thermal current Ith of 50 A at temperatures up to 60 °C for the main circuit.

For the signaling auxiliary circuit, the specified conventional thermal current is 10 A at 60 °C.

High electrical and mechanical durability

The TeSys LC1D32F7 is designed for a high number of operations:

  • Mechanical durability: up to 15 million cycles.
  • Electrical durability in AC-3 at 32 A: approximately 1.65 million cycles.
  • Electrical durability in AC-1 at 50 A: approximately 1.4 million cycles.
  • Maximum operating rate: up to 3600 cycles per hour at temperatures up to 60 °C.

These performance values make it suitable for automation applications with repetitive switching over long service periods.

Coil consumption

The coil requires higher power during the initial closing instant and lower consumption once the contactor is held in the energized position.

  • Inrush power: approximately 70 VA at 50/60 Hz.
  • Holding consumption at 50 Hz: approximately 7 VA.
  • Holding consumption at 60 Hz: approximately 7.5 VA.
  • Thermal dissipation: approximately 2-3 W.

These values should be considered when sizing transformers, relays, or circuits used to supply the control coil.

Fast switching times

Schneider Electric specifies reduced operating times:

  • Closing time: between 12 and 22 ms.
  • Opening time: between 4 and 19 ms.

This speed allows it to respond immediately to signals from the control circuit in automation applications.

DIN rail or plate mounting

The LC1D32F7 offers two main installation options:

  • DIN rail mounting.
  • Direct plate mounting.

This flexibility makes it easy to integrate into both compact electrical panels and larger industrial automation cabinets.

Screw terminals

The power and control circuits use screw terminals. For the power circuit, Schneider Electric allows connections of up to 10 mm² depending on the type and number of conductors used.

The specified tightening torque is approximately:

  • Power circuit: 2.5 Nm.
  • Control circuit: 1.7 Nm.

The final conductor cross-section must be calculated according to load current, installation method, temperature, and applicable regulations.

Compact 45 mm wide format

The contactor has reduced dimensions to help maximize available panel space:

  • Width: 45 mm.
  • Height: 85 mm.
  • Depth: 92 mm.
  • Weight: approximately 0.375 kg.

Its format allows several contactors and control devices to be installed in a reduced space while maintaining an orderly layout.

IP20 front protection

The front face of the LC1D32F7 has an IP20 protection rating according to IEC 60529. It must be installed inside a suitable enclosure that provides the degree of protection required by the operating environment.

The contactor also includes a protective cover and TH protection treatment in accordance with IEC 60068-2-30.

Environmental conditions

The contactor is designed to operate under a wide range of conditions:

  • Operating ambient temperature: from -5 to 60 °C.
  • Storage temperature: from -60 to 80 °C.
  • Operating altitude: up to 3000 m without temperature derating.
  • Pollution degree: 3.
  • Fire resistance: 850 °C according to IEC 60695-2-1.
  • Flammability rating: V1 according to UL 94.

Compatible with TeSys accessories

The LC1D32F7 can be combined with Schneider Electric TeSys accessories and components to create complete switching, protection, and automation solutions, including:

  • Motor thermal overload relays.
  • Additional auxiliary blocks.
  • Timed modules.
  • Surge suppression modules.
  • Mechanical interlocks.
  • Reversing accessories.
  • Connection and mounting systems.

This modularity makes it easy to adapt the contactor to different motor control and industrial automation architectures.

Applications of the Schneider Electric LC1D32F7

Thanks to its 32 A rating and 110 V coil, it can be used in many professional applications:

  • Direct-on-line starting of three-phase motors.
  • Pumps and booster sets.
  • Fans and extractors.
  • Compressors.
  • HVAC and air conditioning systems.
  • Industrial machinery.
  • Conveyor belts.
  • Automation panels.
  • Resistive loads.
  • Systems controlled by PLCs, relays, or pushbuttons.

Standards and certifications

The contactor is designed in accordance with different international standards applicable to switching and control devices:

  • IEC 60947-4-1.
  • IEC 60947-5-1.
  • EN 60947-4-1.
  • EN 60947-5-1.
  • UL 508.
  • CSA C22.2 No. 14.

Schneider Electric documentation also lists international certifications such as UL, CSA, CCC, DNV, BV, RINA, and Lloyd's Register, among others.

Technical data of the Schneider Electric LC1D32F7

  • Manufacturer: Schneider Electric.
  • Range: TeSys.
  • Family: TeSys D / TeSys Deca.
  • Reference: LC1D32F7.
  • Type: contactor.
  • Application: motor control and resistive loads.
  • Categories: AC-1, AC-3 and AC-4.
  • Poles: 3P.
  • Main contacts: 3 NO.
  • Auxiliary contacts: 1 NO + 1 NC.
  • AC-3 current: 32 A up to 440 V.
  • AC-1 current: 50 A up to 440 V.
  • Coil voltage: 110 V AC.
  • Coil frequency: 50/60 Hz.
  • Motor at 220-230 V: 7.5 kW.
  • Motor at 380-400 V: 15 kW.
  • Motor at 415-440 V: 15 kW.
  • Motor at 500 V: 18.5 kW.
  • Motor at 660-690 V: 18.5 kW.
  • Motor at 400 V in AC-4: 7.5 kW.
  • Maximum AC operating voltage: 690 V.
  • Maximum DC operating voltage: 300 V.
  • Ui: 690 V according to IEC.
  • Uimp: 6 kV.
  • Overvoltage category: III.
  • Ith power circuit: 50 A at 60 °C.
  • Ith auxiliary circuit: 10 A at 60 °C.
  • Making capacity: 550 A at 440 V.
  • Breaking capacity: 550 A at 440 V.
  • Mechanical durability: 15 million cycles.
  • Electrical durability AC-3: approximately 1.65 million cycles.
  • Maximum operating rate: 3600 cycles/h.
  • Mounting: DIN rail or plate.
  • Connections: screw terminals.
  • Front protection rating: IP20.
  • Width: 45 mm.
  • Height: 85 mm.
  • Depth: 92 mm.
  • Weight: approximately 0.375 kg.
  • Operating temperature: -5 to 60 °C.
  • Storage temperature: -60 to 80 °C.

32 A TeSys contactor with 110 V coil

The Schneider Electric LC1D32F7 combines a rated current of 32 A in AC-3, capability for three-phase motors up to 15 kW at 400 V, and a 110 V AC 50/60 Hz control coil. Its three normally open main contacts perform the power switching, while the integrated 1 NO + 1 NC auxiliary contacts facilitate interlocking, signaling, and system control.

Its 45 mm width, DIN rail or plate mounting, high durability, and compatibility with TeSys accessories make this contactor a versatile solution for motor control panels, pumps, fans, machinery, HVAC, and industrial automation.

The final selection should be made taking into account the actual load power and current, utilization category, mains voltage, switching frequency, and environmental conditions of the installation.

Specifications
Manufacturer
SCHNEIDER ELECTRIC
Reference
LC1D32F7
SKU
SCH966985B2
Object
Contactor
Number of poles
3 NA
Assembly
Plate. Profile
Warranty
18 months
Compliance with RoHS
YES
Number of contacts
1 NA + 1 NC A
Operating temperature
-20.00 - 60.00 °C
Datasheets
Reviews
Returns within 30 days
Shop with peace of mind. If something goes wrong, we'll take care of it.
After-sales service
Any questions? Our support team will be happy to help you.
Pay how and when you want
Card, bank transfer, PayPal... Installment? We have them all.
GroupSumi is your online distributor for construction, electrical material and climate control.
All rights reserved © 2026 GroupSumi