

The Schneider Electric A9C20847 is a modular contactor from the Acti9 iCT range designed for remote control and switching of electrical lighting, heating, and small motor circuits. It features 4 poles with 4 normally closed contacts (4 NC), a rated operational current of 40 A in AC-7A category, and a control coil of 220-240 V AC at 50 Hz. Its modular design makes it easy to install on a 35 mm DIN rail in residential, commercial, and tertiary electrical panels.
The iCT A9C20847 contactor enables automated connection and disconnection of loads via a maintained electrical control signal. It includes a front mechanical indicator for easy visual verification of contact status and is ready to be combined with compatible Schneider Electric Acti9 control auxiliaries.
The A9C20847 has four normally closed power contacts. When the control coil is not energized, the contacts remain closed; when the coil is energized, the contactor changes state and opens all four circuits.
This 4 NC configuration is suitable for automation systems where several circuits need to remain connected at rest and be opened simultaneously by an electrical command.
Schneider Electric specifies a rated operational current of 40 A in AC-7A category for this contactor. This category is mainly intended for slightly inductive loads used in domestic and similar applications.
For motor loads classified under AC-7B, the specified rated operational current is 15 A. The load connected to the contactor must be selected according to its nature, utilization category, and the conditions established by Schneider Electric.
Parameter Value AC-7A rated current 40 A AC-7B rated current 15 A Rated operational voltage 400 V AC Frequency 50 Hz Number of poles 4 Configuration 4 NCThe control circuit operates at a voltage of 220 to 240 V AC at 50 Hz. This control voltage allows the contactor to be integrated directly into many residential and commercial electrical panels supplied at mains voltage.
The manufacturer’s holding power consumption for the coil is 6.5 VA, while the inrush apparent power reaches 53 VA.
Schneider Electric designs the Acti9 iCT range for controlling different types of loads. The A9C20847 can be used for remote switching operations in applications such as:
The contactor must always be selected according to the type of load and the corresponding utilization category, since the permissible current can vary considerably between resistive loads, lighting, and motors.
The contactor includes a front mechanical position indicator that allows the device status to be visually identified. This feature makes inspection, commissioning, and maintenance of the electrical panel easier.
The front also includes a large labeling area, making it easier to identify the controlled circuit in installations with multiple contactors and modular devices.
The Schneider Electric Acti9 iCT A9C20847 is designed for clip-on installation on a 35 mm symmetrical DIN rail. Its width corresponds to 6 x 9 mm steps, equivalent to approximately 3 DIN modules.
This format allows it to be integrated alongside circuit breakers, residual current devices, timers, and other modular components within standardized electrical panels.
The A9C20847 has a mechanical durability of up to 1,000,000 cycles. Electrical life depends on the utilization category and the connected load.
Condition Electrical durability 40 A, AC-7A 100,000 cycles 15 A, AC-7B 30,000 cycles AC-1 100,000 cycles AC-3 30,000 cyclesSchneider Electric specifies a maximum reference switching frequency of 100 switching operations per day.
The contactor uses screw-type tunnel terminals for both the power circuit and the control circuit.
Connection Capacity Power circuit, flexible conductor 6 to 16 mm² Power circuit, rigid conductor 6 to 25 mm² Control circuit, rigid conductor 1.5 to 2.5 mm² Control circuit, flexible conductor 1.5 to 2.5 mm² Power circuit tightening torque 3.5 Nm Control circuit tightening torque 0.8 NmThe Schneider Electric A9C20847 is compatible with various control auxiliaries from the Acti9 family, allowing the contactor’s functions to be expanded within the electrical panel.
Among the accessories and auxiliaries indicated by Schneider Electric are the iACTc, iACTp, iACTs, and iATEt families. Exact compatibility should be verified according to the required function and the final system configuration.
The Schneider Electric Acti9 iCT A9C20847 modular contactor complies with IEC/EN 61095, the standard applicable to electromechanical contactors for household and similar uses. The range is designed for integration into Acti9 modular distribution and automation systems.
The Schneider Electric A9C20847 Acti9 iCT is a modular solution for automating the switching of electrical circuits, combining four normally closed contacts, 40 A capacity in AC-7A, a 220-240 V AC coil, DIN rail mounting, and integration with Acti9 control auxiliaries.