Contactor ICT 40A 4 NO 230/240V AC with reference A9C21844 from the brand SCHNEIDER ELECTRIC
Contactor ICT 40A 4 NO 230/240V AC with reference A9C21844 from the brand SCHNEIDER ELECTRIC
SCHNEIDER ELECTRIC

Contactor ICT 40A 4 NO 230/240V AC

REF
A9C21844
(0)
158.00 €
€158.00
€429.69
Up to -6% for professionals. Discover it.
Schneider Electric Acti9 iCT modular contactor 4P 40A with 4 NO contacts, 220-240V AC 50Hz coil and manual/remote control, ideal for lighting, heating and small motors.
Buy now and receive it between 20 and November 23
Express delivery
Get +158 +316 Sumis for the purchase
Receive 2x Sumis for a limited time
More about the product

Information about Contactor ICT 40A 4 NO 230/240V AC

The Schneider Electric Acti9 iCT modular contactor A9C21844 is a control device with 4 poles and 4 normally open contacts (4 NO), designed for remote control of lighting, heating, ventilation and small motors. It offers a rated operational current of 40 A in AC-7A category and 15 A in AC-7B category, with a control coil of 220-240 V AC at 50 Hz.

In addition to remote electrical control, this model includes manual operation via a front selector, making commissioning, maintenance operations and local circuit switching easier. It is part of the Acti9 modular range and is installed directly on a 35 mm DIN rail, occupying 3 modules of 18 mm.

Key features of the Schneider Electric A9C21844

  • Brand: Schneider Electric.
  • Range: Acti9.
  • Product: Acti9 iCT.
  • Reference: A9C21844.
  • Type: modular contactor.
  • Number of poles: 4P.
  • Contact composition: 4 NO.
  • Rated current AC-7A: 40 A.
  • Rated current AC-7B: 15 A.
  • Control voltage Uc: 220-240 V AC.
  • Control frequency: 50 Hz.
  • Rated operational voltage Ue: 400 V AC.
  • Control: manual and remote.
  • Applications: lighting, heating and small motors.
  • Mounting: symmetrical 35 mm DIN rail.
  • Width: 54 mm, equivalent to 3 modules of 18 mm.
  • Protection rating: IP20.
  • Standard: IEC/EN 61095.

4 normally open contacts

The A9C21844 has four normally open contacts. In the rest position, the four poles remain open and, when the coil receives the corresponding control signal, the contactor switches and closes the contacts to supply the connected loads.

This 4-pole configuration allows simultaneous switching of several conductors or circuits within the applications supported by the manufacturer, providing a single switching point for the load.

40 A in AC-7A category

Schneider Electric specifies a rated operational current of 40 A in AC-7A category. This category mainly covers low-inductive loads commonly used in domestic, residential and commercial applications, such as certain heating circuits and similar loads.

For motor loads corresponding to AC-7B category, the indicated rated operational current is 15 A. The contactor must always be selected taking into account the type of load and not only the maximum current shown on the front.

220-240 V AC control coil

The contactor coil operates with a control voltage of 220 to 240 V AC at 50 Hz. This voltage allows it to be directly integrated into many automation and control circuits powered from common low-voltage networks.

Control is carried out by a maintained signal: while the appropriate supply is applied to the coil, the contacts remain in the actuated position.

Manual and remote operation

A distinguishing feature of this reference is the combination of remote control and manual control. The front selector allows direct intervention on the contactor without relying exclusively on the electrical control signal.

Schneider Electric specifies a four-position selector that allows:

  • Automatic operation.
  • Temporary ON command.
  • Permanent ON.
  • OFF.

This functionality makes installation testing easier and provides local control for certain maintenance or service operations.

Applications in lighting, heating and ventilation

The Acti9 iCT A9C21844 is designed for the control of lighting, heating, ventilation and small motors. It can be used, for example, for remote switching of loads via thermostats, time switches, relays, home automation systems or compatible energy management devices.

Possible applications include:

  • Lighting circuits.
  • Electric heating systems.
  • Fans.
  • Small motors.
  • HVAC systems.
  • Time-controlled circuits.
  • Residential and commercial automation.
  • Remote management of electrical loads.

Rated operational voltage of 400 V AC

The contactor has a rated operational voltage Ue of 400 V AC at 50 Hz. Its rated insulation voltage Ui is 500 V AC and the rated impulse withstand voltage Uimp reaches 4 kV.

These characteristics allow its use in properly designed distribution and control panels, always respecting the utilization categories and electrical limits specified by Schneider Electric.

Low coil consumption

The control circuit has a holding consumption of approximately 6.5 VA, while the inrush or pick-up consumption reaches approximately 53 VA.

These values must be taken into account when sizing control transformers, relays, timers or other devices responsible for supplying the contactor coil.

Mechanical position indicator

The contactor includes a mechanical contact position indicator. This element makes it possible to visually check the device status from the front of the panel, facilitating monitoring and maintenance operations.

Local indication is especially useful in panels with multiple devices, as it allows the contactor status to be identified quickly without removing components.

Compatible with Acti9 auxiliaries

The A9C21844 is compatible with different Acti9 control auxiliaries, allowing its functions to be expanded depending on the installation requirements.

Schneider Electric specifies compatibility with accessories from the following families:

  • iACTs.
  • iACTc.
  • iACTp.
  • iATEt.

Thanks to this modular architecture, it is possible to integrate additional signalling, control and automation functions while maintaining consistency with the Acti9 system.

DIN rail mounting

The contactor is designed for clip-on mounting on a 35 mm symmetrical DIN rail. Its modular format makes it easy to incorporate into residential, commercial and small automation panels.

It occupies 6 steps of 9 mm, equivalent to a total width of 54 mm or 3 modules of 18 mm.

Compact dimensions

  • Width: 54 mm.
  • Height: 85 mm.
  • Depth: 60 mm.
  • Color: white.
  • Packed unit weight: approximately 361 g.

Its modular format makes it easy to install alongside miniature circuit breakers, residual current devices, timers and other devices belonging to the Acti9 system.

Electrical connection

The device uses tunnel terminals for power and control circuits. Schneider Electric specifies the following main connection capacities:

  • Power circuit with rigid conductor: up to 25 mm².
  • Power circuit with flexible conductor: up to 16 mm².
  • Control circuit: conductors up to 2.5 mm² depending on configuration.
  • Power circuit tightening torque: 3.5 Nm.
  • Control circuit tightening torque: 0.8 Nm.

The cross-section used must be selected according to the load current, installation conditions and the applicable electrical regulations.

High mechanical durability

Schneider Electric declares a mechanical durability of up to 1,000,000 cycles, allowing the contactor to be used in applications where switching operations occur frequently.

Electrical durability depends on the utilization category and the switched load:

  • AC-7A at 40 A: up to 100,000 cycles.
  • AC-7B at 15 A: up to 30,000 cycles.

The manufacturer indicates a utilization frequency of up to 100 switching operations per day under the specified conditions.

Quiet operation

The sound level declared by Schneider Electric is approximately 30 dB. This feature is especially interesting in panels installed in homes, offices, shops and other occupied spaces where reducing noise from switching devices is important.

Environmental conditions

The A9C21844 is designed to operate within a wide range of environmental conditions:

  • Operating temperature: -5 to 60 °C.
  • Storage temperature: -40 to 70 °C.
  • Relative humidity: up to 95% at 55 °C.
  • Maximum operating altitude: 2,000 m.
  • Pollution degree: 2.
  • Protection rating: IP20.

Compliant with IEC/EN 61095

The Acti9 iCT modular contactor is designed in accordance with IEC/EN 61095, applicable to electromechanical contactors intended for domestic and similar uses.

Schneider Electric mainly targets this product at the residential and small commercial segments, although the suitability of the device must be verified according to the load and electrical characteristics of each installation.

Technical data of the Schneider Electric A9C21844

  • Manufacturer: Schneider Electric.
  • Range: Acti9.
  • Series: iCT.
  • Reference: A9C21844.
  • EAN: 3606480096877.
  • Type: modular contactor.
  • Application: motor, heating and lighting.
  • Number of poles: 4P.
  • Contacts: 4 NO.
  • Rated current AC-7A: 40 A.
  • Rated current AC-7B: 15 A.
  • Control voltage Uc: 220-240 V AC.
  • Control frequency: 50 Hz.
  • Operational voltage Ue: 400 V AC.
  • Insulation voltage Ui: 500 V AC.
  • Impulse withstand voltage Uimp: 4 kV.
  • Control type: manual and remote.
  • Signal type: maintained.
  • Manual selector: 4 positions.
  • Position indicator: mechanical.
  • Holding consumption: 6.5 VA.
  • Inrush consumption: 53 VA.
  • Thermal dissipation: approximately 2.1 W.
  • Maximum indicated frequency: 100 operations/day.
  • Mechanical durability: up to 1,000,000 cycles.
  • Electrical durability AC-7A: up to 100,000 cycles.
  • Electrical durability AC-7B: up to 30,000 cycles.
  • Mounting: clip-on 35 mm DIN rail.
  • Width: 54 mm.
  • Height: 85 mm.
  • Depth: 60 mm.
  • Modular width: 3 modules of 18 mm.
  • Protection rating: IP20.
  • Sound level: 30 dB.
  • Operating temperature: -5 to 60 °C.
  • Storage temperature: -40 to 70 °C.
  • Maximum altitude: 2,000 m.
  • Standard: IEC/EN 61095.

Acti9 modular contactor for controlling loads up to 40 A

The Schneider Electric A9C21844 is a modular switching solution for installations that need to control lighting, heating, ventilation or other equipment from an external electrical signal. Its four normally open contacts allow simultaneous control of four poles, while the front selector provides manual control in addition to remote operation.

With 40 A in AC-7A, 15 A in AC-7B, a 220-240 V AC coil, mechanical position indicator and 3-module DIN mounting, this Acti9 iCT contactor integrates easily into residential and commercial panels. Compatibility with Acti9 auxiliaries also allows its control and automation functions to be expanded according to project needs.

Specifications
Manufacturer
SCHNEIDER ELECTRIC
Reference
A9C21844
SKU
SCHE76B9693
Object
Contactor
Tension
220.00 - 240.00 V
Number of poles
4 NO
Assembly
Adjustable in clip
Network type
CA
Protection rating
IP20
Frequency
50.00 - 60.00 Hz
Datasheets
Reviews
Returns within 30 days
Shop with peace of mind. If something goes wrong, we'll take care of it.
After-sales service
Any questions? Our support team will be happy to help you.
Pay how and when you want
Card, bank transfer, PayPal... Installment? We have them all.
GroupSumi is your online distributor for construction, electrical material and climate control.
All rights reserved © 2026 GroupSumi