Contactor ICT 63A 2 NO 230/240V AC with reference A9C20862 from the brand SCHNEIDER ELECTRIC
Contactor ICT 63A 2 NO 230/240V AC with reference A9C20862 from the brand SCHNEIDER ELECTRIC
SCHNEIDER ELECTRIC

Contactor ICT 63A 2 NO 230/240V AC

REF
A9C20862
(0)
126.00 €
€126.00
€342.31
Up to -6% for professionals. Discover it.
Schneider Electric Acti9 iCT modular contactor 2P 63 A, 2 NO, 230-240 V AC 50 Hz coil, 63 A AC-7A and 20 A AC-7B, for lighting, heating, ventilation and small motors.
Buy now and receive it between 20 and November 23
Express delivery
Get +126 +252 Sumis for the purchase
Receive 2x Sumis for a limited time
More about the product

Information about Contactor ICT 63A 2 NO 230/240V AC

The Schneider Electric Acti9 iCT A9C20862 modular contactor is a remote control device with 2 poles and 2 normally open contacts (2 NO), designed for switching lighting, heating, ventilation, and small motors. It offers a rated operational current of 63 A in AC-7A category and 20 A in AC-7B, with a control circuit of 220-240 V AC at 50 Hz. Its 36 mm modular design makes it easy to install on DIN rail in residential and commercial electrical panels.

The A9C20862 reference belongs to Schneider Electric's Acti9 iCT range and is specifically designed to automate loads using thermostats, timers, relays, energy management systems, or other control devices. It includes a mechanical contact position indicator, low-noise operation, and compatibility with Acti9 control auxiliaries.

63 A bipolar modular contactor

The Schneider Electric A9C20862 incorporates 2 normally open power poles. In the absence of voltage at the coil, the contacts remain open; when the control circuit energizes the coil, both contacts close and supply the connected load.

  • Number of poles: 2P.
  • Contact composition: 2 NO.
  • Control type: remote control.
  • Control signal type: maintained.
  • Network type: AC.

63 A in AC-7A category

The 63 A rating corresponds to the AC-7A utilization category, intended mainly for domestic or similar resistive or slightly inductive loads.

This type of use includes applications such as:

  • Electric heating.
  • Certain lighting circuits.
  • Resistive loads.
  • Compatible air conditioning and ventilation systems.
  • Other receivers within the specified operating conditions.

20 A in AC-7B category

For applications corresponding to the AC-7B category, Schneider Electric specifies a rated operational current of 20 A.

This category covers loads with motor characteristics, so it is especially important not to interpret the 63 A AC-7A rating as an admissible current of 63 A for any type of motor.

  • AC-7A: 63 A.
  • AC-7B: 20 A.

Schneider Electric expressly indicates that the iCT can be used for the remote switching of small motors, such as fans or mixers, provided the electrical characteristics of the load are compatible.

220-240 V AC control coil

The A9C20862 reference includes a 220-240 V AC control coil at 50 Hz. This voltage allows it to be directly integrated into many control circuits powered from the mains.

The contactor can be controlled by different devices, such as:

  • Time switches.
  • Thermostats.
  • Control relays.
  • Detectors.
  • Home automation systems.
  • HVAC controllers.
  • Energy management systems.

250 V AC operational voltage

Schneider Electric specifies for this configuration a rated operational voltage Ue of 250 V AC at 50 Hz.

Its main insulation characteristics are:

  • Rated insulation voltage Ui: 500 V AC.
  • Rated impulse withstand voltage Uimp: 4 kV.
  • Pollution degree: 2.

Coil consumption

The control circuit has the following approximate consumption values:

  • Inrush power: 34 VA.
  • Holding power: 4.6 VA.

These values make it possible to correctly size the device controlling the coil, especially when several contactors are operated from the same control system.

Mechanical position indicator

The Acti9 iCT A9C20862 includes a mechanical contact position indicator. This signaling makes it possible to visually check the switching status of the contactor from the front of the panel.

It also features a large area for circuit identification, making labeling easier in panels with multiple devices.

Low-noise operation

Schneider Electric highlights the low noise level of the Acti9 iCT range. For this reference, an approximate noise level of 30 dB is specified.

This feature is especially useful in residential installations, offices, shops, and other spaces where the electrical panel is located near occupied areas.

DIN rail mounting

The contactor is designed for clip-on mounting on a 35 mm symmetrical DIN rail.

  • Mounting type: clip-on.
  • Support: 35 mm DIN rail.
  • 9 mm steps: 4.
  • Width: 36 mm.
  • Modular equivalent: 2 modules of 18 mm.

Its modular format allows it to be installed alongside miniature circuit breakers, residual current devices, time switches, and other Acti9 family components.

Compact dimensions

  • Height: 85 mm.
  • Width: 36 mm.
  • Depth: 68.5 mm.
  • Color: white RAL 9003.

The two-module format makes it possible to have a bipolar contactor rated up to 63 A AC-7A while occupying a reduced space inside the panel.

Power terminals

The power circuit uses tunnel terminals prepared for large cross-section conductors.

  • Rigid conductor: 6 to 25 mm².
  • Flexible conductor: 6 to 16 mm².
  • Power circuit tightening torque: 3.5 Nm.

Proper tightening of the connections is especially important in high-current circuits to avoid contact resistance and abnormal heating.

Control circuit terminals

For control connections, the contactor accepts different conductor combinations using tunnel terminals.

  • Typical control cross-sections: approximately 1.5-2.5 mm² depending on type and number of conductors.
  • Control circuit tightening torque: 0.8 Nm.

High durability

Schneider Electric specifies a high mechanical service life for this reference:

  • Mechanical durability: up to 1,000,000 cycles.
  • Electrical durability AC-7A at 63 A: up to 100,000 cycles.
  • Electrical durability AC-7B: up to 30,000 cycles.

Actual electrical durability depends on the utilization category, current, voltage, and characteristics of the switched load.

Switching frequency

The technical data sheet specifies a utilization frequency of up to 100 switching operations per day within the conditions indicated for this device.

The contactor is mainly intended for periodic automatic control of loads, not for functions requiring extremely fast or continuous switching.

Compatible with Acti9 auxiliaries

The A9C20862 is compatible with different Acti9 control auxiliaries, allowing the system functions to be expanded according to panel requirements.

It can be part of solutions designed for the control of:

  • Lighting.
  • Heating.
  • Ventilation.
  • Air conditioning.
  • Energy management.
  • Small motors.

Degree of protection

Schneider Electric specifies:

  • Device degree of protection: IP20 according to IEC 60529.
  • In suitable modular enclosure: up to IP40.

The contactor must be installed inside a panel or enclosure that provides the level of protection required by the environmental conditions of the installation.

Environmental conditions

  • Operating temperature: -5 to 60 °C.
  • Storage temperature: -40 to 70 °C.
  • Relative humidity: up to 95% at 55 °C.
  • Maximum operating altitude: 2,000 m.

Applications of the Schneider Electric A9C20862

The Acti9 iCT modular contactor is especially suitable for automating loads in residential, commercial, and small tertiary panels.

  • Electric heating.
  • Lighting.
  • Ventilation systems.
  • HVAC equipment.
  • Fans.
  • Compatible small motors.
  • Load automation via time switch.
  • Thermostat control.
  • Energy management systems.
  • Residential and commercial electrical panels.

Technical characteristics of the Schneider Electric A9C20862

  • Brand: Schneider Electric.
  • Reference: A9C20862.
  • Range: Acti9.
  • Family: Acti9 iCT.
  • Type: modular contactor.
  • Applications: lighting, heating, ventilation, and small motors.
  • Number of poles: 2P.
  • Composition: 2 NO.
  • Rated current AC-7A: 63 A.
  • Rated current AC-7B: 20 A.
  • Rated operational voltage Ue: 250 V AC.
  • Control circuit voltage Uc: 220-240 V AC.
  • Control circuit frequency: 50 Hz.
  • Control signal type: maintained.
  • Coil inrush power: 34 VA.
  • Coil holding power: 4.6 VA.
  • Rated insulation voltage Ui: 500 V AC.
  • Rated impulse withstand voltage Uimp: 4 kV.
  • Pollution degree: 2.
  • Mechanical position indicator: yes.
  • Noise level: approximately 30 dB.
  • Mounting: 35 mm symmetrical DIN rail.
  • Width: 36 mm.
  • Height: 85 mm.
  • Depth: 68.5 mm.
  • Modular width: 2 modules of 18 mm.
  • Color: white RAL 9003.
  • Rigid power conductor: 6-25 mm².
  • Flexible power conductor: 6-16 mm².
  • Power tightening torque: 3.5 Nm.
  • Control tightening torque: 0.8 Nm.
  • Mechanical durability: 1,000,000 cycles.
  • Electrical durability AC-7A: 100,000 cycles.
  • Electrical durability AC-7B: 30,000 cycles.
  • Indicated switching frequency: 100 operations/day.
  • Degree of protection: IP20.
  • Protection in modular enclosure: IP40.
  • Operating temperature: -5 to 60 °C.
  • Storage temperature: -40 to 70 °C.
  • Maximum altitude: 2,000 m.
  • Standard: IEC/EN 61095.
  • EAN: 3606480375132.

Modular contactor for load automation

The Schneider Electric Acti9 iCT A9C20862 combines two normally open contacts, a 63 A AC-7A rating, and 220-240 V AC control in a compact format of only two modules. It is especially designed to automate lighting, heating, and ventilation, as well as compatible small motors.

Its mechanical position indicator, low-noise operation, high durability, and compatibility with Acti9 auxiliaries make it easy to integrate into residential and commercial panels controlled by timers, thermostats, and other automation devices.

Important: the A9C20862 is a switching contactor and not a protection device. It does not replace miniature circuit breakers, fuses, residual current devices, or motor protection devices. The 63 A rating applies to AC-7A category; for AC-7B motor loads, the specified rated current is 20 A. The associated protection must be sized according to the load and the characteristics of the installation.

Specifications
Manufacturer
SCHNEIDER ELECTRIC
Reference
A9C20862
SKU
SCHB3C58C55
Object
Contactor
Tension
220.00 - 240.00 V
Number of poles
2 NO
Assembly
Adjustable in clip
Network type
CA
Protection rating
IP20
Frequency
50.00 - 60.00 Hz
Datasheets
Reviews
Returns within 30 days
Shop with peace of mind. If something goes wrong, we'll take care of it.
After-sales service
Any questions? Our support team will be happy to help you.
Pay how and when you want
Card, bank transfer, PayPal... Installment? We have them all.
GroupSumi is your online distributor for construction, electrical material and climate control.
All rights reserved © 2026 GroupSumi