

The Schneider Electric A9C20736 is a modular contactor from the Acti9 iCT range, designed for remote control and switching of electrical circuits for lighting, heating, and small motors. It features 2 poles with 2 normally closed contacts (2 NC), a rated operational current of 25 A in AC-7A category, and a control coil of 230-240 V AC at 50 Hz, providing a compact solution for residential and commercial distribution boards.
Its slim 18 mm width allows installation in a single standard DIN module. The device includes a mechanical contact position indicator, maintained control signal operation, and compatibility with Acti9 control auxiliaries, making it easy to integrate into automation and load management systems.
The A9C20736 has 2 poles with NC contacts. In the rest state, when the coil is not energized, the contacts remain closed. When voltage is applied to the control circuit, the contactor switches and opens both poles.
This configuration makes it suitable for circuits where the load must remain energized while the contactor is at rest and be disconnected by an electrical control command.
Schneider Electric specifies a rated operational current of 25 A in AC-7A category. This category covers domestic and similar loads with a slightly inductive character, including common heating and lighting applications.
For motor loads in AC-7B category, the specified rated operational current is 8.5 A.
Utilization category Rated current AC-7A 25 A AC-7B 8.5 AThe contactor includes a control coil designed for a voltage of 230 to 240 V AC at 50 Hz. This allows it to be operated directly from control circuits compatible with standard mains voltage.
The control signal type is maintained: the contactor remains energized while the coil is supplied with voltage and returns to its rest position when the control supply is removed.
Feature Value Control voltage Uc 230-240 V AC Control circuit frequency 50 Hz Signal type Maintained Holding consumption 2.7 VA Peak power 9.2 VASchneider Electric defines the Acti9 iCT as a modular contactor intended mainly for the control of lighting, heating, and motors. The A9C20736 can be used to automate loads from time switches, thermostats, building management systems, or other compatible control devices.
It can also be used for remote switching of small motors, such as fans or mixers, provided the current and utilization category are compatible with the contactor specifications.
The front of the device includes a mechanical contact position indicator. This feature makes it easy to visually check the contactor status during inspection, commissioning, or maintenance of the electrical panel.
One of the main advantages of the A9C20736 is its compact size. With a width of only 18 mm, equivalent to two 9 mm pitches or one standard DIN module, it makes maximum use of the available panel space.
Dimension Value Height 81 mm Width 18 mm Depth 68.5 mm 9 mm pitches 2 Color WhiteThe contactor is designed for clip-on installation on a 35 mm symmetrical DIN rail. This format makes it easy to integrate alongside miniature circuit breakers, residual current devices, timers, time switches, and other Acti9 modular devices.
Schneider Electric also incorporates a mechanical and electrical clip connection system between contactors up to 25 A and certain compatible auxiliaries in the range.
The A9C20736 is compatible with various Acti9 control auxiliaries, including devices from the iACTc, iACTs, iACTp, and iATEt families. These accessories expand control, signaling, or timing options according to the installation requirements.
The exact compatibility and configuration of the assembly should be checked in Schneider Electric documentation before installation.
The contactor uses tunnel terminals for power and control circuits. Schneider Electric specifies different permissible conductor cross-sections depending on the type and number of conductors used.
Circuit Conductor Cross-section Power supply Flexible 1 to 4 mm² Power supply Rigid 1.5 to 6 mm² Control Rigid 1.5 to 2.5 mm² Control Flexible 1.5 to 2.5 mm²The tightening torque specified by Schneider Electric is 0.8 Nm for both the power circuit terminals and the control circuit terminals.
The A9C20736 is designed for applications requiring repeated switching operations. Schneider Electric declares a mechanical durability of up to 1,000,000 cycles.
Durability Value Mechanical 1,000,000 cycles Electrical AC-7A at 25 A 100,000 cycles Electrical AC-7B at 8.5 A 30,000 cyclesThe switching frequency indicated by the manufacturer is up to 100 operations per day within the product’s specified conditions.
The contactor offers an IP20 protection rating according to IEC 60529. When correctly installed in a suitable modular enclosure, Schneider Electric indicates an IP40 protection level for the front assembly.
The Schneider Electric Acti9 iCT A9C20736 is especially suitable for automation and remote switching of loads in residential and small commercial electrical panels.
The A9C20736 complies with IEC/EN 61095, applicable to electromechanical contactors for domestic and similar uses. Correct device selection should take into account the load current, utilization category, switching frequency, and circuit protection devices.
The Schneider Electric A9C20736 Acti9 iCT is a compact solution for automating lighting, heating, and small motor circuits. Its 2 normally closed contacts, 25 A AC-7A capacity, 230-240 V AC coil, one-module DIN format, and mechanical indicator make it easy to integrate into residential and commercial electrical panels.