

The Schneider Electric Acti9 iCT A9C21834 modular contactor is a switching device with 4 poles and 4 normally open contacts (4 NO), designed for controlling lighting circuits, heating, ventilation, and small motors. It offers a rated operational current of 25 A in AC-7A category and features a 230/240 V AC control coil, as well as both remote control and manual operation directly from the front.
Thanks to its modular format of only 36 mm width and 35 mm DIN rail mounting, the A9C21834 can be easily integrated into residential, commercial, and professional electrical panels. Its manual override is especially practical during commissioning, maintenance, or installation testing.
The Schneider Electric A9C21834 has 4 poles and 4 normally open main contacts. When the coil is energized, the four contacts change state simultaneously, allowing the associated loads to be connected to the circuit.
The contactor incorporates a coil designed for use with a 230/240 V AC control voltage. Schneider Electric technical documentation specifies a control range of 220 to 240 V AC at 50 Hz.
This control voltage makes it possible to integrate the contactor directly into many common automation and control circuits used in building electrical installations.
One of the standout features of this reference is the inclusion of manual control in addition to remote operation. The front selector allows the contactor to be operated directly from the electrical panel, making testing and maintenance tasks easier.
It also includes a mechanical contact position indicator, which allows the contactor status to be checked visually.
Schneider Electric develops the Acti9 iCT range specifically for switching common loads in residential and commercial buildings. The A9C21834 is suitable for applications such as:
Its ability to receive remote commands also makes it easy to integrate with time switches, energy management systems, thermostats, relays, and other compatible automation devices.
The contactor has a rated operational current of 25 A in AC-7A category, corresponding to domestic and similar applications with slightly inductive loads.
For motor loads in AC-7B category, Schneider Electric specifies a rated current of 8.5 A. These characteristics make it possible to use the same device in different applications, always respecting the utilization category corresponding to the connected load.
In addition to the AC-7A and AC-7B categories defined for domestic and similar applications, the technical documentation allows its use in different categories according to applicable standards, including:
Permissible current and electrical durability depend on the utilization category and the specific type of connected load.
The control circuit is designed to keep consumption low during operation. Schneider Electric specifies a holding consumption of 4.6 VA and an inrush consumption of approximately 34 VA.
The Acti9 iCT A9C21834 is designed to perform numerous operations over its service life. Its mechanical durability reaches up to 1,000,000 cycles.
In AC-7A category at 25 A, the specified electrical durability is up to 100,000 cycles. In categories such as AC-7B, AC-3, AC-5A, or AC-5B, the declared value is up to 30,000 cycles under the conditions specified by the manufacturer.
The Schneider Electric A9C21834 is compatible with Acti9 range control auxiliaries, allowing the automation, timing, signaling, and management capabilities of the contactor to be expanded.
This compatibility makes it easy to create complete lighting, heating, or ventilation control systems using modular components from the same family.
The contactor is designed for clip-on installation on a 35 mm symmetrical DIN rail. It occupies four 9 mm modules, equivalent to 36 mm width.
The device has a rated insulation voltage Ui of 500 V AC and an impulse withstand voltage Uimp of 4 kV, suitable for use inside low-voltage electrical panels.
The Schneider Electric Acti9 iCT A9C21834 is a versatile solution for automating the switching of electrical loads from a modular panel. Its 25 A in AC-7A, 4 poles with 4 NO contacts, and 230/240 V AC coil make it especially suitable for lighting, heating, and ventilation systems.
The integrated manual override, mechanical status indicator, compatibility with Acti9 auxiliaries, and compact DIN rail format also provide flexibility for new installations, expansions, and building automation projects.